Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Wiki Markup
{scroll-pagetitle}Product Specifications{scroll-pagetitle}
||*Environmental Characteristics*||
|Operating Ambient Temperature Range|-20°C to 65°C|
|Storage/Transport Ambient Temperature Range|-40°C to 85°C|
|High Impact Shock|MIL-STD-901D, Grade A|
|Mechanical Vibration|MIL-STD-167B|
|Electro-Magnetic Interference|MIL-STD-461E|
|Facial Protection|NEMA 4|
|Housing Protection|NEMA 4|

\\
||*Input Power*||
|Voltage Range| 18 to 36 VDC|
|Typical Power Consumption Range*|4 to 10 Watts (not including Aux. DC Output)|
*Reference the Electrical Installation [Power|PDG:Power (FAC2100)] section for more information.

\\
||*Analog Outputs*||
|Quantity / Resolution|2 Channels / 14 Bits|
|Current Output Ranges Supported|0-20mA, 4-20mA|
|Current Output Range Accuracy|+/-40uA at 25°C, +/-100uA Over Temperature|
|Voltage Output Ranges Supported|0-10V, 0-5V|
|Voltage Output Range Accuracy|+/-40mV at 25°C, +/-100mV Over Temperature|

\\
{page-break}
||*Analog Inputs*||
|Quantity / Resolution|3 Channels / 16 Bits|
|Current Input Ranges Supported|0-20mA, 4-20mA|
|Current Input Accuracy|+/-40uA at 25°C, +/-100uA Over Temperature|
|Standard Voltage Input Ranges Supported|0-20V, 0-10V, 0-5V, 1-5V, 0-2.5V|
|Standard Voltage Input Range Accuracy|+/-36mV at 25°C, +/-86mV Over Temperature|
|Low Voltage Input Ranges Supported|0-1V, 0-500mV, 0-250mV, 0-100mV|
|Low Voltage Input Range Accuracy|+/-2mV at 25°C, +/-5mV Over Temperature|
|Resistance Input Range Supported|0-2400Ω|
|Resistance Input Range Accuracy|+/-2.4 or +/-0.4% of Reading (whichever is smaller) Over Temperature|
|RTD Support|3 Wire, 100Ω Platinum (European or American curve), 120Ω Nickel, or Custom|
|RTD Accuracy|+/- 1°C Over Temperature|

\\
||*Standard Digital Inputs*||
|Quantity / Type|8 Channels / Opto-isolated|
|Maximum Allowable Continuous Input Voltage|200 VDC or 140 VAC RMS|
|Maximum Allowable Voltage Spike|1000V peak 1.2µS x 50µS pulse per MIL-STD-1399 Section 300|
|Logic High Voltage Range|5-200 VDC or 24-130 VAC 55-500 Hz|
|Minimum Input Duration for Logic High Detection|4 ms|
|Logic Low Voltage Range|0-1 VDC or 0-0.5 VAC 55-500 Hz|
|Minimum Input Duration For Logic Low Detection|56 ms|
|Minimum Input Current Required (AC and DC inputs)|5mA RMS|

\\
{page-break}
||*Universal Digital Inputs*||
|Quantity / Type|2 Channels / Opto-isolated|
|Input Signal Support|5VDC, 28VDC (at approximately 7mA)|
|Single-Input Operating Modes|on/off (i.e., switch), pulse counter, frequency counter|
|Dual-Input Operating Modes|event timer, quadrature decoder|
|Maximum Frequency|500 KHz|
\\
||*Low Power Digital Outputs*||
|Quantity / Type|2 Channels / Opto-isolated Transistor|
|Output Signal Support|Up to 28VDC (40mA maximum)|
|Operating Modes|on/off, variable frequency square-wave, pulse width modulation (PWM)|
|Maximum Frequency|50 Hz|

\\
||*High Power Digital Outputs*||
|Quantity / Type|5 Relays Maximum / Up to 4 Mechanical Form “C” Relays and up to 3 Opto-isolated Solid State Form “A” Relays|
|Mechanical Relay Rated Signal Range|4 A (resistive) @ 24VDC or 120 VAC, 2 A (resistive) @240 VAC|
|Solid State Relay Rated Signal Range|3 A @ 60VDC or 140 VAC|
Reference the [Mechanical |PDG:Mechanical Relay Output Interface (FAC2100)] and [Solid State|PDG:Solid State Relay Output Interface (FAC2100)] Relay sections for more information.

\\
||*Displays*||
|Element Type|Yellow, Green, and Red LEDs|
|Digital Readouts|Two 4 digit, 7 segment digital readouts \\
One 3 digit, 7 segment digital readout \\
Colors are user-specified \\
0.4" in height \\
0.3" in width|
|Analog Bar Graphs|Two columns of 40 LEDs (colors are user-specified) \\
4" in height \\
0.2" in width \\
0 to 100% range \\
2.5% bargraph operation resolution|
|Alpha-numeric Displays|Three rows with 8 characters (7x5 pixel resolution) each|
|Keypad|Six positive tactile-feel keys|

\\
{page-break}
||*Network Support*||
|Point to Point|RS-232 (maximum of 2 devices)|
|Multi-drop|RS-485 and RS-422|

\\
||Turn On Time||
|Less then 5 seconds|

\\
||*Programming Method*||
|_Design Pad_ graphical programming environment on a PC using Windows XP or better --- Compiled programs are typically transferred from a PC's COMM port to the controller via RS-232 serial link|

\\
||*Local Adjustments*||
|Outputs and user-specified properties are adjusted using a six-button keypad|

\\
||*Dimensions*||
|Front|5.5" x 8"|
|Depth (w/o cylindrical connector shells)|7.75"|

\\
||*Weight*||
|Approximately 7 pounds|

\\
{page-break}
{scroll-ignore}
[!FA_Inclusion_Library^FAprev.png!|PDG:Networking Options (FAC2100)] [!FA_Inclusion_Library^FAnext.png|PDG:align=right!|Installation (FAC2100)]
{scroll-ignore}